Hikrobot MV-CIS-308mm-06-U0F1M

Line-scan tasks and range position

A 7360-pixel monochrome line captured at up to 95.5 kHz is the defining capability of MV-CIS-308mm-06-U0F1M. The CMOS contact image sensor uses a 7360 × 1, 1-Line arrangement with 42.34 μm pixels and sends data through an LC fiber connector. Exposure can be set from 3 μs to 10 ms, while the stepped gain choices run from 2.0 × through 8.0 ×. This combination addresses continuous surface acquisition where one line is built into an image by material travel.

The 95.5 kHz line rate supports moving web, sheet and document inspection when transport speed and line timing are coordinated. A short 3 μs exposure can reduce along-travel blur under sufficient illumination, and the selectable gain stages provide adjustment for signal level. Camera power and light-source power enter through separate functions on 12-pin P10 connections: the camera draws 26.4 W at 24 VDC and the light source 3.8 W at 24 VDC. The LC fiber path separates image transfer from those power connections.

Against MV-CIS-330mm-18-91F2M and MV-CIS-330mm-18-91F2M/package, this model trades line length and TDI modes for higher single-line speed. Both longer-line entries provide 23424 × 3 sampling, 1-Line plus 2-TDI and 3-TDI operation, and 81 kHz in 1-Line mode or 27 kHz in the TDI modes. Choose MV-CIS-308mm-06-U0F1M for 7360 × 1 acquisition at 95.5 kHz and an LC connector; choose either 23424-pixel designation for the longer line, TDI choices and 2LC interface.

Documents

Selection and applications

Continuous monochrome web inspection. High-rate sheet surface scanning. Fiber-linked line acquisition.

Minimum kit: The minimum setup is the MV-CIS-308mm-06-U0F1M contact image sensor assembly, its imaging optics and light source, an LC fiber cable, and 24 VDC feeds rated for the camera and light-source loads.

Nearby in the range: MV-CIS-330mm-18-91F2M — Prefer it for a 23424-pixel line, 2-TDI or 3-TDI operation, and a 2LC fiber connection; MV-CIS-330mm-18-91F2M/package — Prefer this designation when the required item is the /package variant with 23424 × 3 imaging.

FAQ

What line rate can MV-CIS-308mm-06-U0F1M sustain at full length?

The listed maximum is 95.5 kHz for its 7360-pixel, 1-Line output. System timing must relate that line frequency to transport motion so successive 7360 × 1 captures form the required image geometry. The optical data connection is an LC fiber connector.

How are the camera and its light source powered and connected?

A 24 VDC supply is required. The CAM_PWR function on a 12-pin P10 connector provides camera power and I/O, while LED_PWR on another 12-pin P10 connection powers the light source. Rated loads are 26.4 W for the camera and 3.8 W for the light source.

Which exposure and gain controls are available for moving material?

Exposure spans 3 μs to 10 ms. Gain is selectable in stated steps from 2.0 × to 8.0 ×, including 2.4 ×, 2.8 ×, 3.3 ×, 4.0 ×, 4.7 ×, 5.5 × and 6.75 ×. Those controls let integration time and amplification be balanced against line motion and illumination.

What installation conditions apply to this contact image sensor?

The working range is –20 °C to 50 °C, with 5% RH to 90% RH and no condensation. Storage is rated from –30 °C to 80 °C. IP40 applies under proper lens installation and wiring, so the final machine arrangement must preserve those stated conditions.

When should MV-CIS-308mm-06-U0F1M be chosen over the longer-line entries?

Choose MV-CIS-308mm-06-U0F1M when a 7360 × 1 monochrome line at up to 95.5 kHz and an LC fiber connector match the acquisition plan. The longer-line entries instead provide 23424 × 3 resolution, a 2LC connection, and selectable 1-Line, 2-TDI or 3-TDI scanning.