Cis line scan camera · CIS Series
Hikrobot MV-CIS-330mm-18-91F2M/package
- Lead time
- from 5 days
- Warranty
- 36 months
Package variant in the CIS range
Selectable line accumulation and a 23424-pixel span characterize MV-CIS-330mm-18-91F2M/package. The monochrome CMOS contact image sensor records 23424 × 3 through 14 μm × 14 μm pixels. Its 1-Line mode reaches 81 kHz; 2-TDI and 3-TDI modes reach 27 kHz. Data leaves through a 2LC fiber connector. The /package suffix distinguishes this catalog entry, while its recorded acquisition and electrical values match the unsuffixed model.
This configuration addresses continuous inspection of broad moving material where the transport direction builds the image line by line. The 1-Line setting serves the higher-rate path, while 2-TDI and 3-TDI provide the listed multi-line choices. Both camera and light source operate from 24 VDC. Their separate 2-pin inputs carry typical loads of 23.4 W for the camera and 31.8 W for the always-on light source, and a separate 12-pin P10 connector handles camera I/O.
Compared with MV-CIS-308mm-06-U0F1M, the package entry increases the line from 7360 × 1 to 23424 × 3 and adds 2-TDI and 3-TDI, but its top 1-Line rate is 81 kHz rather than 95.5 kHz. MV-CIS-330mm-18-91F2M is its direct counterpart: both use 2LC fiber and share the same resolution, mode rates, dimensions and power ratings. Choose between those two by the exact required designation, not by an imaging-performance difference.
Specifications
| Sensor resolution | 23424 px1 |
| Maximum line rate | 81000 Hz @ 1-line; 27000 Hz @ 2-line TDI/3-line TDI |
| Line/TDI image mode | single line, 2-TDI, 3-TDI |
| Color mode | mono1 |
| Working distance | 15 mm |
| Field width | 330 mm |
| Data interface | XoFLink |
| Pixel density | 1800 dpi |
| Sensor technology | CMOS |
| Pixel size | 14×14 µm1 |
| Dynamic range | 68.1 dB |
| Signal-to-noise ratio | 44.3 dB |
| Exposure time | 8…10000 µs |
| Auto exposure | Off, Once, Continuous |
| Linear gain factor | 1 |
| Pixel format | Mono8, Mono10, Mono12 |
| Binning | 1x1, 1x2, 1x4, 2x1, 2x2, 2x4, 4x1, 4x2, 4x4 |
| Trigger mode | external, internal; line @ external trigger |
| Working distance tolerance | 0.6 mm |
| Data interface connector | LC ×2 |
| Protocol compatibility | GenICam |
| Client software | MVS |
| Operating systems | Windows 7 (32/64-bit), Windows 10 (32/64-bit), Windows 11 (64-bit) |
| Digital I/O connector | P10 12-pin |
| Ingress protection | IP40 @ with lens and cables properly installed |
| Working temperature | 0…50 °C |
| Storage temperature | -30…80 °C |
| Humidity | 5…90 % @ non-condensing |
| Dimensions | 404×94.5×136.6 mm (without light source); 404×94.5×140.6 mm (with light source) |
| Weight | 4500 g (approx.) |
| Certification | CE, RoHS, KC |
| Camera component power consumption | 23.4 W (typical) @ DC, supply voltage 24 V |
| Camera component supply voltage | 24 V @ DC |
| Light source component power consumption | 31.8 W (typical) @ DC, always on, supply voltage 24 V |
| Light source component supply voltage | 24 V @ DC |
| Transmission mode | two links |
| Reverse image | horizontal |
1 unofficial data
Documents
Selection and applications
Broad-web monochrome inspection. Selectable TDI scanning. Package-designated CIS integration.
Minimum kit: The minimum setup is the MV-CIS-330mm-18-91F2M/package contact image sensor assembly with its imaging optics and light source, a 2LC fiber cable, two 24 VDC power branches, and a 12-pin P10 I/O connection.
Nearby in the range: MV-CIS-308mm-06-U0F1M — Prefer it when 7360 × 1 at 95.5 kHz and a single LC fiber connection suit the line; MV-CIS-330mm-18-91F2M — Choose it when the required designation omits /package; its imaging and power ratings match.
FAQ
Which acquisition modes are included in MV-CIS-330mm-18-91F2M/package?
The scan choices are 1-Line, 2-TDI and 3-TDI. Maximum line rate is 81 kHz in 1-Line and 27 kHz in either TDI setting. The monochrome CMOS sensor has 23424 × 3 resolution and a 14 μm × 14 μm pixel size.
How should data, power and I/O be separated for this package entry?
Use the 2LC fiber connector for image data. Supply 24 VDC separately to the camera and light source through their 2-pin connectors, then use the 12-pin P10 connector for camera I/O. The listed architecture therefore keeps data, both power branches and timing distinct.
What are the continuous power loads of the two 24 VDC branches?
The camera has a typical load of 23.4 W at 24 VDC. The always-on light source has a typical load of 31.8 W at 24 VDC. Each has a dedicated 2-pin power connector, so the electrical design should account for both stated branches.
What mechanical envelope applies when the light source is installed?
The assembly measures 404 mm × 94.5 mm × 136.6 mm without the light source and 404 mm × 94.5 mm × 140.6 mm with it. Installation clearance should therefore be based on the latter dimensions when the listed light source is fitted.
How does this package designation compare with the unsuffixed model?
Both entries carry the same 23424 × 3 sensor format, 81 kHz and 27 kHz mode rates, 2LC interface, dimensions, 24 VDC feeds and typical power values. Selection between them follows whether the required catalog designation includes /package.