Line scan camera · CL Series
Hikrobot MV-CL082-91F1M
- Lead time
- from 5 days
- Warranty
- 36 months
8K mono fiber capture with two scan modes
An 8192 × 2 mono CMOS array and LC fiber connection define MV-CL082-91F1M. The 7 × 7 µm pixels deliver 146 kHz in 1-Line mode and 100 kHz in 2-TDI. Exposure runs from 3 µs to 10 ms, dynamic range is 63.4 dB, and the stated gain is 1.0×. This profile combines a long scan line with two acquisition modes for fiber-linked systems.
Wide moving webs, sheets or surfaces can use the 8192 samples for dense coverage across the target, while the selected line rate sets sampling along its motion. Four configurable input/output signals are carried on the 12-pin P10 power/I/O connector and support single-ended or differential operation. That division keeps machine timing on the control connection while the image stream travels through fiber.
MV-CL082-91F2M keeps the 8192 × 2 mono geometry but uses a 2LC fiber connector and raises the maximum to 200 kHz. MV-CL082-92CM offers the same sensor length and 2-TDI over Camera Link, reaching 100 kHz in 80-bit mode in a 76 mm × 76 mm × 42.1 mm body. MV-CL081-41CM is the single-row Camera Link alternative, with an 80 kHz Full-mode ceiling and a lower typical consumption of 5.8 W.
Available versions
One device, different revisions. We ship the current one by default; if a specific revision is already installed on your line, name it in the request and we will match it.
| Part number | PN | Version | |
|---|---|---|---|
| MV-CL082-91F1M discontinued | 306302444 | — | |
| MV-CL082-91F1M V2.0 | 306303815 | V2.0 |
Specifications
| Sensor resolution | 8192×2 px |
| Maximum line rate | 146000 Hz @ 1-line; 100000 Hz @ 2-line TDI |
| Line/TDI image mode | single line, 2-TDI |
| Color mode | mono |
| Lens mount | M72×0.75 |
| Data interface | XoFLink |
| Sensor technology | CMOS |
| Pixel size | 7×7 µm |
| Dynamic range | 63.4 dB |
| Signal-to-noise ratio | 40.8 dB |
| Exposure time | 3…10000 µs |
| Auto exposure | Auto, Off, Once, trigger width |
| Linear gain factor | 1 |
| Pixel format | Mono8, Mono10, Mono12 |
| Binning | 1x1, 1x2, 1x4, 2x1, 2x2, 2x4, 4x1, 4x2, 4x4 |
| Trigger mode | external, internal; line, frame, line and frame @ external trigger |
| Flange focal distance | 12 ±0.15 mm |
| Data interface connector | LC |
| Protocol compatibility | XoFLink, GenICam |
| Client software | MVS |
| Operating systems | Windows 7 (32/64-bit), Windows 10 (32/64-bit), Windows 11 (64-bit) |
| Digital I/O lines | 4 bidirectional lines, single-ended, differential, lines 0, 1, 3, 4 |
| Digital I/O connector | P10 12-pin |
| Power supply | 12…24 V @ DC |
| Power consumption | 11.1 W (typical) @ DC, supply voltage 24 V |
| Ingress protection | IP40 @ with lens and cables properly installed |
| Working temperature | -20…50 °C |
| Storage temperature | -30…80 °C |
| Humidity | 5…90 % @ non-condensing |
| Dimensions | 132×76×57.4 mm |
| Weight | 600 g (approx.) |
| Certification | CE, RoHS, KC |
| Mounts via adapter | F-mount (via adapter) |
| Transmission mode | one link |
| Power supply connector | P10 12-pin |
| Reverse image | horizontal |
Documents
Selection and applications
8K mono inspection over fiber. 2-TDI wide-web scanning. Single-line acquisition at 146 kHz.
Minimum kit: Use the MV-CL082-91F1M camera, an M72*0.75 line-scan lens or adapted F-mount lens, an LC fiber cable and receiver, and a 12 V DC to 24 V DC source on the 12-pin P10 connector.
Nearby in the range: MV-CL082-91F2M — Prefer it when the 8192 × 2 fiber line must reach 200 kHz; MV-CL082-92CM — Prefer it when Camera Link is the installed acquisition interface; MV-CL081-41CM — Prefer it for a single-row 8192-pixel sensor and 5.8 W typical consumption.
Cables and accessories for this model
Compatibility per manufacturer data.
- I/O & power cables
- 12-pin IO
- Power
- Power
- Mounting
- Camera mounts
FAQ
What rates are available in each MV-CL082-91F1M scan mode?
The camera reaches 146 kHz in 1-Line mode and 100 kHz in 2-TDI. Both use the 8192 × 2 mono sensor with 7 µm pixels, so the choice depends on the required TDI arrangement and line density along the moving target.
How should optics be matched to the MV-CL082-91F1M line?
MV-CL082-91F1M uses an M72*0.75 mount with a 12 mm flange back length. F-mount optics are supported through an adapter; the lens must cover all 8192 pixels and resolve the 7 × 7 µm pitch.
What powers MV-CL082-91F1M and carries its control I/O?
The 12-pin P10 connector supplies 12 V DC to 24 V DC power and four configurable I/O lines with single-ended or differential signaling. Typical consumption is 11.1 W at 24 V DC. Fiber image transfer uses the separate LC connector.
What environmental protection is provided by MV-CL082-91F1M?
The camera works from -20 °C to 50 °C at 5% RH to 90% RH without condensation and stores from -30 °C to 80 °C. IP40 applies under proper lens installation and wiring, so external protection is needed against liquids and substantial dust.
How does MV-CL082-91F1M differ from MV-CL082-91F2M?
Both are 8192 × 2 mono fiber cameras with 7 µm pixels and 1-Line/2-TDI modes. MV-CL082-91F1M uses an LC connector and reaches 146 kHz in 1-Line, while MV-CL082-91F2M uses 2LC and reaches 200 kHz.