Line scan camera · CL Series
Hikrobot MV-CL084-91CM
- Lead time
- from 5 days
- Warranty
- 36 months
Four-row 8K mono with Camera Link
An 8192 × 4 mono CMOS array with 5 µm pixels gives MV-CL084-91CM both long cross-object sampling and three row-mode choices. It supports 1-line, 2-TDI and 4-TDI acquisition. Camera Link rates are 20 kHz in Base, 40 kHz in Medium, 80 kHz in Full and 100 kHz in 80-bit operation, with an SDR connector used for data and USB used for firmware updates.
The four-row architecture suits wide mono surface inspection where illumination and travel speed can be addressed through the selected TDI mode. Exposure spans 3 µs to 10 ms and six gain settings run from 1.2× to 6.2×. A 12-pin P10 connector supplies power and four configurable I/O lines, while Camera Link CC1/CC2/CC3/CC4 can also participate in acquisition timing.
MV-CL082-92CM reduces the array to 8192 × 2 with 7 µm pixels and 2-TDI, while retaining the same 100 kHz 80-bit ceiling in a smaller 76 mm body. MV-CL084-91CM-PRO expands to 8192 × 16 and adds control for as many as 4 lamps, with a 75 kHz 1-lamp Full rate. MV-CL084-91F2M keeps 8192 × 4 but uses 7 µm pixels and 2LC fiber, reaching 200 kHz in 1-Line, 1-light mode.
Specifications
| Sensor resolution | 8192×4 px |
| Maximum line rate | 20000 Hz @ Base; 40000 Hz @ Medium; 80000 Hz @ Full; 100000 Hz @ 80-bit (Deca) |
| Line/TDI image mode | single line, 2-TDI, 4-TDI |
| Color mode | mono |
| Lens mount | M72×0.75 |
| Data interface | Camera Link |
| Sensor technology | CMOS |
| Pixel size | 5×5 µm |
| Dynamic range | 62 dB |
| Signal-to-noise ratio | 42 dB |
| Exposure time | 3…10000 µs |
| Auto exposure | Off, Once, Continuous, fixed exposure time, trigger width |
| Linear gain factor | 1.2 2.7 3 Show all (6)3.54.6 6.2 |
| Pixel format | Mono8, Mono10, Mono12 |
| Binning | 1x1, 2x2, 4x4 |
| Trigger mode | external, internal; line, frame @ external trigger; line, frame @ external trigger, line + frame trigger |
| Flange focal distance | 12 mm |
| Data interface connector | Camera Link SDR |
| Protocol compatibility | Camera Link, GenICam |
| Communication protocol versions | Camera Link 1.2 |
| Third party software protocol | Camera Link |
| Client software | MVS |
| Operating systems | Windows 7 (32/64-bit), Windows 10 (32/64-bit), Windows 11 (64-bit) |
| Digital I/O lines | 4 bidirectional lines, single-ended, differential, lines 0, 1, 3, 4 |
| Power supply | 12…24 V |
| Power consumption | 9.7 W (typical) @ DC, supply voltage 12 V |
| Ingress protection | IP40 @ with lens and cables properly installed |
| Working temperature | -20…55 °C |
| Storage temperature | -30…80 °C |
| Humidity | 5…90 % @ non-condensing |
| Dimensions | 84×84×46.2 mm |
| Weight | 476 g (approx.) |
| Certification | CE, RoHS2.0, KC |
| Camera Link configuration | Base, Medium, Full, 80-bit |
| Mounts via adapter | F-mount (via adapter) |
| Camera link control lines | CC1, CC2, CC3, CC4 |
| Pixel clock | 40000000 Hz; 66000000 Hz; 80000000 Hz; 85000000 Hz |
| Port inventory | Camera Link ×2 (data), USB (firmware update) |
| Reverse image | horizontal |
| Tap count | 2; 4; 8; 10 |
| Tap geometry | 1X2, 1X4, 1X8, 1X10 |
Documents
Selection and applications
8K four-row mono inspection. Camera Link 4-TDI scanning. Wide-surface capture at 100 kHz.
Minimum kit: Pair the MV-CL084-91CM camera with an M72*0.75 line-scan lens or adapted F-mount lens, a Camera Link cable and frame grabber, and a 12 V DC to 24 V DC supply on the 12-pin P10 connector.
Nearby in the range: MV-CL082-92CM — Prefer it for an 8192 × 2 sensor in a 76 mm Camera Link body; MV-CL084-91CM-PRO — Prefer it for an 8192 × 16 array with multi-lamp control; MV-CL084-91F2M — Prefer it for 8192 × 4 mono capture at 200 kHz over 2LC fiber.
Cables and accessories for this model
Compatibility per manufacturer data.
- Data cables
- Camera Link
- I/O & power cables
- 12-pin IO
- Power
- Power
- Mounting
- Camera mounts
FAQ
Which row modes are supported by the MV-CL084-91CM array?
The 8192 × 4 mono sensor supports 1-line, 2-TDI and 4-TDI modes. Its 5 µm pixels can be read at up to 20 kHz in Base, 40 kHz in Medium, 80 kHz in Full and 100 kHz in 80-bit Camera Link operation.
What gain and exposure controls are available on MV-CL084-91CM?
Exposure is adjustable from 3 µs to 10 ms. Listed gain selections are 1.2×, 2.7×, 3.0×, 3.5×, 4.6× and 6.2×, providing discrete settings for matching the mono sensor response to the illumination arrangement.
How should a lens be mounted on the MV-CL084-91CM?
MV-CL084-91CM has an M72*0.75 interface and a 12 mm flange back length. F-mount lenses can be fitted via an adapter. The optic must cover the full 8192-pixel line and resolve the 5 µm pixel pitch.
What are the MV-CL084-91CM power and I/O provisions?
Provide 12 V DC to 24 V DC through the 12-pin P10 connector and allow for 9.7 W typical consumption at 12 V DC. Four configurable single-ended or differential I/O lines are available, together with Camera Link CC1/CC2/CC3/CC4.
How does MV-CL084-91CM differ from MV-CL084-91CM-PRO?
The standard model uses an 8192 × 4 mono array, reaches 100 kHz in 80-bit mode and draws 9.7 W typically. The PRO version uses 8192 × 16, adds multi-lamp control, takes 24 V DC and draws 22.9 W typically.