Line scan camera · CL Series
Hikrobot MV-CL083-B0F2C
- Lead time
- from 5 days
- Warranty
- 36 months
A 71 kHz 8K color fiber variant
A 71 kHz full-width color line distinguishes MV-CL083-B0F2C among the 8192 × 3 models. The CMOS sensor uses 7 × 7 µm pixels, 1-Line scanning and a 2LC fiber interface. Its exposure range is 3 µs to 10 ms, dynamic range is 61.2 dB, and gain steps of 1.0×, 2.0×, 3.0× and 4.0× provide optical-level adjustment.
This model addresses wide color surface inspection where the acquisition timing is handled outside the camera I/O, because digital I/O is not supported. The 2LC fiber path carries the image stream, while the camera takes 12 V DC to 24 V DC and draws a typical 15.8 W at 12 V DC. The body measures 132 mm × 76 mm × 55.5 mm and uses an M72*0.75 lens interface.
MV-CL083-91F2C uses the same 8192 × 3 color geometry and 2LC transport, reaches 66.6 kHz and adds four configurable I/O lines on a 12-pin P10 connector. MV-CL083-92CC changes to Camera Link, reaching 33.7 kHz at full width or 66.6 kHz at 4140 pixels and below. MV-CL084-B1NC uses 2.5 Gigabit Ethernet and runs at 37.6 kHz in full-resolution Mono 8/Bayer RG 8.
Specifications
| Sensor resolution | 8192×3 px |
| Maximum line rate | 71000 Hz |
| Line/TDI image mode | single line |
| Color mode | color |
| Lens mount | M72×0.75 |
| Data interface | XoFLink |
| Sensor technology | CMOS |
| Pixel size | 7×7 µm |
| Dynamic range | 61.2 dB |
| Signal-to-noise ratio | 40.1 dB |
| Exposure time | 3…10000 µs |
| Auto exposure | Off, Once, Continuous, fixed exposure time, trigger width |
| Linear gain factor | 1; 2; 3; 4 |
| Pixel format | RGB8, BGR8, Mono8, BayerRG8, BayerRG10 |
| Binning | 1x1, 1x2, 1x4, 2x1, 2x2, 2x4, 4x1, 4x2, 4x4 |
| Trigger mode | external, internal; line @ external trigger |
| Flange focal distance | 12 mm |
| Protocol compatibility | XoFLink, GenICam |
| Client software | MVS |
| Operating systems | Windows 7 (32/64-bit), Windows 10 (32/64-bit), Windows 11 (64-bit), Linux (32/64-bit) |
| Digital I/O lines | not available |
| Power supply | 12…24 V |
| Power consumption | 15.8 W (typical) @ DC, supply voltage 12 V |
| Ingress protection | IP40 @ with lens and cables properly installed |
| Working temperature | -20…50 °C |
| Storage temperature | -30…80 °C |
| Humidity | 5…90 % @ non-condensing |
| Dimensions | 132×76×55.5 mm |
| Weight | 600 g (approx.) |
| Certification | CE, RoHS, KC |
| Mounts via adapter | F-mount (via adapter) |
| Transmission mode | one link, two links |
| Reverse image | horizontal |
Documents
Selection and applications
8K color scanning at 71 kHz. Dual-fiber wide-surface inspection. Color acquisition without camera I/O.
Minimum kit: Use the MV-CL083-B0F2C camera, an M72*0.75 line-scan lens or adapted F-mount optic, a 2LC fiber cable and receiver, and a 12 V DC to 24 V DC supply.
Nearby in the range: MV-CL083-91F2C — Prefer it when the 2LC color camera must provide four configurable I/O lines; MV-CL083-92CC — Prefer it when the acquisition system is based on Camera Link; MV-CL084-B1NC — Prefer it for 2.5 Gigabit Ethernet transport and a 76 mm body width.
Cables and accessories for this model
Compatibility per manufacturer data.
- Power
- Power
- Mounting
- Camera mounts
FAQ
Does MV-CL083-B0F2C provide trigger or general-purpose digital I/O?
No. The digital I/O entry states that it is not supported. The integration must therefore account for acquisition coordination outside a camera I/O connection while receiving the 8192 × 3 color stream over the 2LC fiber interface.
What is the maximum full-line rate of MV-CL083-B0F2C?
The stated maximum is 71 kHz for the 8192 × 3 color CMOS sensor in 1-Line operation. Pixel pitch is 7 × 7 µm, exposure ranges from 3 µs to 10 ms and selectable gains extend from 1.0× to 4.0×.
Which optics attach to the MV-CL083-B0F2C housing?
The native thread is M72*0.75 with a 12 mm flange back length. F-mount optics may be fitted through an adapter, with coverage selected for the complete 8192-pixel color line and resolution appropriate to 7 µm pixels.
How should power be sized for an MV-CL083-B0F2C station?
The supply range is 12 V DC to 24 V DC and typical consumption is 15.8 W at 12 V DC. Image data uses the separate 2LC fiber interface, and the power design should not assume camera-side digital I/O because that function is unsupported.
What environmental limits apply to MV-CL083-B0F2C?
The camera operates from -20 °C to 50 °C at 5% RH to 90% RH without condensation and stores from -30 °C to 80 °C. IP40 applies with proper lens installation and wiring, so liquid and substantial dust require external protection.